LDP SHARP XG-MB55X-L problem

proyektor
(LDP) merek: SHARP-MB55X model ig-L dengan keluhan total kematian, baik
indikator LED menyala / siaga (keluhan yang umumnya sangat digemari
oleh teknisi tersebut). Tapi tidak semua begitu mudah semua perangkat ..

1.Buka lima baut di bagian bawah, empat di sudut jalan, satu di tengah2.Buka cover / casing di atas, terlihat panel kontrol papan.3.Buka empat baut pada setiap sudut regulator blok dari atas, angkat sedikit dan membuka casing logam baut di sebelah samping.4.Lepaskan semua koneksi soket2 (4 ke blower, kabel power, pelindung sirkuit, suatu regulator output)5.Angkat blok / modul hati2 panel kontrol, karena berhubungan langsung dengan blok DSP cahaya.Tentu
saja pertama kali saya cek adalah blok kekuatan suplly; sekering
kondisinya masih normal, tanda-tanda bahwa TR / IC switching
regulatornya tidak pendek.Blok dibagi menjadi dua regulator, satu untuk blok rangkaian utama / blok untuk memasok mainboard dan lampu.Setelah
regulator ternyata mengamati sistem siaga tidak bekerja, hasil
pengukuran ini ternyata regulator menggunakan IC STR-W6575 sistem siaga.Meskipun
tidak ada komponen yang terlihat pendek / dibakar, seiring dengan
pergantian ini IC STR pendukung Resistor dan beberapa elco kecil
(10/35-22/35) .. membuat perangkat ini dapat "mulai" lagi ..Tapi
tunggu, setelah semua terpasang rapi kembali, menonton kabel listrik
bila tegangan input kabel / PLN, bagaimana kondisi indikator nyala
dipimpin dipimpin nya Standb? ..
  1.Bila
masih tidak menyala, usahakan untuk mengkonfirmasi posisi pelindung
sirkuit nya (terletak di sisi depan lampu merah, ketika terprotek, cukup
tekan tombol merah kecil lagi
 2.Bila
LED merah terus berkedip / meliuk, pastikan semua soket telah dipasang
dengan benar, terutama yang mengarah ke soket lampu (AN-XR20LP) dan blok
DSP (Digital Signal prosesor)
  3. Bila LED hijau, kembali ke merah, periksa lampu blok rangkaian, blok elco regulator.Sisanya Anda hanya menunggu rilis dari tampilan seperti ini di dinding Anda.
Catatan,
Anda tidak boleh mencabut kabel daya ketika Anda mematikan / menutup
LDP sebelum indikator LED merah siaga, meskipun lampunya mati.
  Jika
Anda memiliki masalah dengan komponennya, terutama IC, lebih baik Anda
hubungi vendor, kecuali lampu dapat diganti (bila terpaksa) dengan merek
Ben-Q.



projector (LDP) brand: SHARP-MB55X model xg-L with a total death complaint, neither the indicator LED lights up / standby (complaints that are generally very liked by the technician). But not all so easy any devices ..


1.Buka five bolts at the bottom, four on the corner, one in the middle
2.Buka cover / casing above, it appears the board control panel.
3.Buka four bolts on each corner of the block regulators from the top, lift a little and opened an adjoining metal casing bolts on the side.
4.Lepaskan all connections soket2 (4 to a blower, a power cord, a circuit protector, an output regulator)
5.Angkat blocks / modules are hati2 control panel, since it deals directly with DSP blocks the light.
Of course the first time I checked was the power block suplly; fuse his condition was still normal, signs that the TR / IC switching regulatornya not short.
Blocks are divided into two regulators, one for the main circuit blocks / block to supply the mainboard and lamps.
Once the regulator turns out to observe its standby system does not work, the results of these measurements turned out regulator using IC STR-W6575 to its standby system.
Although there is no component who looks short / burnt, along with the turn of this STR IC Resistors supporters and a few small elco (10/35-22/35) .. make this device can "start" again ..
But wait, after all installed neatly back, watch your power cord when the cord input voltage / PLN, how the flame condition led indicator led his Standb? ..
  1.Bila still not lit, try to confirm his position circuit protector (located on the front side of a red light, when terprotek, just press the little red button again
 2.Bila red LED continues to blink / flicker, make sure all the sockets are properly installed, especially leading to the lamp socket (AN-XR20LP) and blocks of DSP (Digital Signal processor)
  3. When the LED is green, back to red, check the circuit block lamp, block elco regulators.
The rest you just wait for the release of this kind look on your wall.

Note, you should never unplug the power cord when you turn off / shut down the LDP before the red standby LED indicator, even though its lights were dead.
  If you have problems with its components, especially IC, it is better you contact the vendor, unless the lamp can be replaced (when forced) with Ben-Q brand.